WP series reducer, the worm is made of 45 # high-quality steel after heat treatment, the worm gear is cast with tin bronze, good wear resistance, especially in bearing capacity is more obvious, mainly suitable for plastics, metallurgy, beverages, mine , Hoist transportation, chemical construction and other mechanical equipment deceleration transmission.
electronic content PDF catalog
1. Stable transmission, low vibration, low impact, low noise, large reduction ratio, strong versatility, suitable for all kinds of mechanical equipment.
2. Single-stage transmission, large transmission ratio, compact structure. Most speed reducers have good self-locking performance, and the braking device can save the mechanical equipment with braking requirements.
3. The friction loss between the worm gear and the tooth surface of the worm gear is large, the transmission efficiency is lower than the gear, it is easy to be heated, and the temperature is higher.
4. Higher requirements for lubrication and cooling.
5. Very good match. Worms and worms are manufactured according to national standards.
B. Working conditions:
1. The speed of the worm reducer should not exceed 1500r / min.
2. The working environment temperature is -40 ° C to + 40 ° C. When the working environment temperature is below 0 ° C, the lubricating oil must be heated to above 0 ° C before starting heating. When the working environment temperature is above 40 ° C, cooling Measures must be taken.
3. The feed shaft of the worm gear reducer can rotate forward or reverse.
1. Worm gear shaft shall not be used as input shaft.
2. The machine does not pump oil when it leaves the factory. Before operation, sufficient mechanical oil must be added.
3. The supporting motor (ie power) shall not exceed the value specified in the sign.
4. If the user wants to change the direction of entering the shaft, please remove the lower end cover of the shaft, take out the worm and adjust 180. Load it. According to the installation without knocking hard, you can slowly drive the two shafts to make it mesh.
|Types of:||WP gearbox|
|Speed ratio:||1: 10,15,20,25,30,40,50,60,200,300,400,500,600,800,900,1200,1 500,1800,2400,2500,3000,3600|
|colour:||Blue / silver or according to customer requirements|
Housing: cast iron casting
Worm gear-copper-10-3 #
Carburized and quenched Worm-20CrMn Ti, the surface harness strength is 56-62HRC
Shaft chrome steel 45 #
|package:||Carton and wooden box|
|Bearing:||C & U Bearing|
|input power.||0.06KW, 0. 09KW, 1.1KW, 1 5KW 2.2KW, 3KW, 4KW, 5 5KW, 7 5KW|
|Application industry:||Industrial machinery: food, ceramics, chemical packaging, dyeing, carpentry, glass.|
|IEC flange:||56B14, 63B14, 63B5, 63B5, 71B14, 80B14, etc.|
WP Single Reducer Ratio has the following models:
WPA40 WPA50 WPA60 WPA70 WPA80 WPA100 WPA120 WPA135 WPA147 WPA155 WPA175 WPA200 WPA250
WPDA50 WPDA60 WPDA70 WPDA80 WPDA100 WPDA120 WPDA135 WPDA147 WPDA155 WPDA175 WPDA200 WPDA250
WPKA40 WPKA50 WPKA60 WPKA70 WPKA80 WPKA100 WPKA120 WPKA135 WPKA155 WPKA175 WPKA200 WPKA250
WPDKA40 WPDKA50 WPDKA60 WPDKA70 WPDKA80 WPDKA100 WPDKA120 WPDKA135 WPDKA155 WPDKA175
WPO40 WPO50 WPO60 WPO70 WPO80 WPO100 WPO120 WPO135 WPO147 WPO155 WPO175 WPO200 WPO250
WPDO50 WPDO60 WPDO70 WPDO80 WPDO100 WPDO120 WPDO135 WPDO147 WPDO155 WPDO175 WPDO200 WPDO250
WPS40 WPS50 WPS60 WPS70 WPS80 WPS100 WPS120 WPS135 WPS147 WPS155 WPS175 WPS200 WPS250
WPDS50 WPDS60 WPDS70 WPDS80 WPDS100 WPDS120 WPDS135 WPDS147 WPDS155 WPDS175 WPDS200 WPDS250
WPKS40 WPKS50 WPKS60 WPKS70 WPKS80 WPKS100 WPKS120 WPKS135 WPKS155 WPKS175 WPKS200 WPKS250
WPDKS50 WPDKS60 WPDKS70 WPDKS80 WPDKS100 WPDKS120 WPDKS135 WPDKS155 WPDKS175
WPX40 WPX50 WPX60 WPX70 WPX80 WPX100 WPX120 WPX135 WPX147 WPX155 WPX175 WPX200 WPX250
WPDX50 WPDX60 WPDX70 WPDX80 WPDX100 WPDX120 WPDX135 WPDX147 WPDX155 WPDX175 WPDX200 WPDX250
WPDZ50 WPDZ60 WPDZ70 WPDZ80 WPDZ100 WPDZ120 WPDZ135
WPDKZ50 WPDKZ60 WPDKZ70 WPDKZ80 WPDKZ100 WPDKZ120 WPDKZ135